Science & engineering

Torque RPM and horsepower calculator

Calculate shaft power or solve torque at a known RPM, keeping mechanical hp and metric PS explicitly separate.

Your numbers

Torque and RPM must refer to the same shaft and operating point. Zero is allowed for power, but not for solving torque.

Calculated on your device. Your inputs aren’t sent to us.

Your result

Ready when you are

Enter your inputs and select Calculate.

Report an issue

Try it, understand it

Explore the result

Compare these worked scenarios while keeping the units and assumptions visible.

Worked example comparison
ExampleOutputWhat to notice
Torque and RPMShaft power78.539816 kWThe existing same-shaft power example is retained.
Direct mechanical power conversionMechanical horsepower1 hp745.699872 W is approximately one mechanical hp.
Original torque exampleShaft power260.989334 kW350 lbf·ft at 5,252 rpm is approximately 350 hp.

Check your understanding

Does direct watts conversion require RPM?

No. It converts power units without calculating torque.

Are mechanical hp and metric PS identical?

No. Their definitions differ.

Behind the numbers

How this calculation works

Normalize the known torque or power, convert revolutions per minute to radians per second, then solve the same-shaft rotational power equation. Show kW, mechanical hp and metric PS using their separate definitions.

THE FORMULAPower W = torque N·m × RPM × 2π / 60; torque N·m = power W / angular speed

A worked example

250 N·m at 3,000 rpm gives 250 × 3,000 × 2π / 60 = 78,539.8163 W, or 78.5398 kW. Conversely, 100 kW at 3,000 rpm corresponds to about 318.3099 N·m at that shaft.

Good to know

Non-negative same-shaft magnitudes at one operating point. No gearing, drivetrain losses, wheel/crank conversion, engine curve or inferred peak rating. Zero RPM gives zero rotational power for finite torque, but cannot be used to solve torque from power. Constant-torque comparisons are mathematical scenarios.

Torque needs rotational speed to give shaft power

Torque describes a turning effect; power describes the rate of doing work. For rotation about the same shaft axis, power in watts equals torque in N·m multiplied by angular speed in radians per second. Revolutions per minute must first be multiplied by 2π and divided by 60.

At 250 N·m and 3,000 rpm, angular speed is about 314.1593 rad/s. Multiplying gives 78,539.8163 W, or 78.5398 kW. Those torque and RPM values must belong to the same operating point. Combining the peak torque from one speed with a maximum RPM from somewhere else does not establish an engine’s actual peak power.

The inverse mode solves torque when power and RPM are known. For 100 kW at 3,000 rpm, 100,000 W divided by 314.1593 rad/s gives about 318.3099 N·m. Conditional fields show the known quantity for the chosen direction; switching modes does not require a second calculator page.

The electrical power calculator uses a DC voltage/current relationship. Shaft power instead combines torque with angular speed at the same shaft, without assuming motor or drivetrain efficiency.

A little curiosity

Horsepower is a family of definitions

The mechanical horsepower used here is 550 foot-pound-force per second, approximately 745.699872 W. Metric horsepower, labeled PS, uses 75 kilogram-force metres per second, or 735.49875 W. They are different units of the same physical quantity, so a power expressed in PS has a different numerical value from one expressed in mechanical hp.

The calculator labels both definitions explicitly and keeps kilowatts alongside them. It does not treat electrical horsepower, boiler horsepower or every historical horsepower label as interchangeable. A technical sheet should identify its unit definition before a comparison is made.

Torque in pound-force feet is also different from a mass in pounds. The conversion used here follows the international pound, international foot and standard gravity. After converting to N·m, the same rotational equation applies. The force calculator covers a separate linear force relationship; torque would additionally require a moment arm and force direction. The hydraulic pump power calculator relates a separate fluid output to an explicitly entered input-efficiency boundary.

Read the constant-torque table as an experiment in the formula

The table holds the entered or solved torque fixed and compares zero, half, equal and double the entered RPM. At constant torque, twice the speed gives twice the power. This illustrates a relationship in the equation. It is not an engine curve and does not assert that the engine can maintain that torque at every displayed speed.

A stationary shaft can have nonzero torque while rotational power is zero, because its angular speed is zero. Forward mode therefore accepts zero RPM. Inverse mode rejects zero RPM because dividing power by zero cannot determine torque; even zero power at zero speed leaves torque undetermined.

No gearing or drivetrain loss is inferred. Engine-shaft power, wheel power and electrical input power refer to different measurement locations or processes. The electrical power calculator uses voltage and current for a DC model; converting that result to mechanical output would require explicit efficiency and operating assumptions. This page does not establish a safe mechanical operating range or a vehicle’s certified rating.

Watts can be converted without inventing an engine curve

The original horsepower address offered a torque/RPM calculation and a watts-to-horsepower conversion. Both are available here. Direct conversion mode converts an entered mechanical power and does not use RPM to invent a torque. The power-from-torque and torque-from-power branches still require a same-shaft operating point.

Mechanical horsepower and metric PS have different definitions. The two labels are reported separately, so rounding both to one generic horsepower factor does not hide a difference. The universal unit converter addresses other measurement dimensions; changing a unit label does not add drivetrain efficiency information.

A power conversion is not motor electrical input power

An electric motor’s electrical input and mechanical shaft output differ through efficiency and operating conditions. Converting watts to mechanical horsepower is only a unit operation when the entered watts already describe the intended power quantity. It does not measure or infer the motor’s losses.

The Ohm’s law calculator reports electrical power for an ideal resistive model, which is a different physical situation. Do not treat those watts as measured motor shaft output without the missing model. Likewise, multiplying torque by RPM at one point does not establish an engine’s peak rated power across its operating range.

A few questions, answered

Why is RPM multiplied by 2π/60?

Each revolution is 2π radians and each minute is 60 seconds. The conversion gives radians per second, which combines with N·m to produce watts.

Are hp and PS the same?

No. This page uses mechanical hp at about 745.699872 W and metric PS at 735.49875 W. Both describe power but use different unit sizes.

Can I calculate torque at zero RPM?

No, not from power using this inverse equation. Forward mode can show zero power at zero RPM for a specified finite torque, but the inverse division is undefined.

Does this predict wheel horsepower or a dyno curve?

No. It calculates a same-shaft relationship at one entered point. The constant-torque speed table is a mathematical comparison without gearing, drivetrain losses or an engine torque curve.

Does direct watts conversion require RPM?

No. It converts power units without calculating torque.

Are mechanical hp and metric PS identical?

No. Their definitions differ.

Find your calculator

Start typing to explore the library.