Science & engineering

LED series resistor and dissipation calculator

Keep a target-current fixed-drop calculation separate from the current at your entered candidate resistance.

Your numbers

An entered fixed component-drop assumption, including 0 V for a pure-resistor comparison; not a diode data-sheet value inferred by this tool.

Calculated on your device. Your inputs aren’t sent to us.

Your result

Ready when you are

Enter your inputs and select Calculate.

Report an issue

Try it, understand it

Explore the result

Compare these worked scenarios while keeping the units and assumptions visible.

Worked example comparison
ExampleOutputWhat to notice
One fixed-drop series stringIdeal resistance at entered target current150 ΩRetain the normal target/candidate comparison.
Original engine-resistor exampleIdeal resistance at entered target current560 Ω14.4 V minus 3.2 V at 20 mA gives 560 Ω.
No positive headroomSeries-resistor resultNo positive voltage headroom for the target currentThe model does not infer actual diode current.

Check your understanding

Does the result select an automotive-rated component?

No. It performs a fixed-drop scenario calculation.

Why can candidate current differ from target current?

The entered candidate resistance can differ from the calculated ideal value.

Behind the numbers

How this calculation works

Subtract the assumed total forward drop for one series string. If positive headroom exists, compare the ideal target resistance with the separately entered candidate and calculate current and dissipations without choosing ratings.

THE FORMULAPositive headroom = Vs − count × Vf; Rtarget = headroom / target amperes; PR = I²R

A worked example

5 V minus a 2 V assumed LED drop leaves 3 V. A 20 mA target gives an ideal 150 Ω and 0.06 W resistor dissipation. The separately entered 180 Ω candidate gives about 16.666667 mA and 0.05 W under the same fixed-drop assumption.

Good to know

One ideal fixed-drop series string. No color lookup, nonlinear I–V/temperature model, standard-value selection, parallel sharing, current-limit approval or power-rating/derating choice. Absent positive headroom does not determine the real diode current.

The resistor receives the supply minus the entire string drop

With a 5 V supply and one assumed 2 V forward drop, the resistor has 3 V across it. The entered 20 mA target is 0.02 A, so the ideal resistance is 3/0.02 = 150 Ω. The resistor’s modeled dissipation is 0.02² × 150 = 0.06 W.

For two identical assumed 2 V LEDs in one series string, the total modeled drop is 4 V, leaving 1 V. The same target current would give 50 Ω. This page handles one series string and does not use a single resistor model to infer sharing among parallel LED branches.

Ohm’s law applies to the resistor after the assumed LED-string voltage has been subtracted. The complete supply voltage is not automatically the resistor voltage.

The entered candidate is a separate operating scenario

The default candidate is 180 Ω, separate from the exact 150 Ω target result. At a fixed 3 V resistor drop, it gives about 16.666667 mA and 0.05 W resistor dissipation. Those calculated powers are not selected component ratings or approvals of a current limit.

Forward voltage is entered, not looked up from color. A real LED’s drop depends on current and conditions, so a fixed-drop calculation is only one scenario. Tolerance, temperature, supply variation and data-sheet limits are not inferred by rounding a resistor value.

No positive headroom means the target calculation no longer applies

At or below the summed assumed forward drop, there is no positive headroom for a positive resistor to establish the target current in this simplified model. The result says so instead of returning a negative resistance or using a zero-ohm value to imply a determined current.

The Ohm’s law calculator can check the resistor’s voltage/current relationship once the appropriate resistor voltage is known. The battery nominal energy and runtime calculator can explore a separate supplied-load energy budget. Neither supplies the LED’s missing nonlinear I–V curve, a current-regulated driver model or a thermal derating choice.

The old engine-resistor address describes a series-drop calculation

The former engine-resistor page subtracted a component voltage from a supply voltage and divided by a target current. The series LED model here covers that same fixed-forward-drop arithmetic while also exposing string count and a separately entered candidate resistor. The result is an ideal resistance and calculated dissipation, not a selected automotive component.

A vehicle’s nominal battery voltage is not a complete description of its electrical environment. Supply changes, transients, temperature and real diode characteristics can make a fixed-voltage example unsuitable as an installation design. The Ohm’s law calculator explains the ideal resistor relation without implying that a wiring environment is fully characterized.

Keep the candidate and target scenarios distinct

The target-current calculation produces an ideal continuous resistance value. A candidate resistor entered by the user generally produces a different current under the same fixed-drop assumptions. Reporting both avoids implying that an arbitrary stocked value preserves the target exactly.

The voltage drop calculator concerns a conductor path and needs additional geometry and material assumptions. Both pages distinguish numerical dissipation from rated capability. A resistor’s power rating, thermal installation and component protection require information beyond an arithmetic watt value.

A few questions, answered

Does the example forward voltage apply to every LED?

No. It is an editable fixed-drop assumption, not a color lookup or data-sheet guarantee.

Does the tool choose a standard resistor value?

No. It reports the exact modeled target resistance and evaluates the candidate value you separately enter.

Is computed resistor power its required marked rating?

No. Ratings and thermal derating are not selected by this arithmetic model.

Does insufficient headroom prove actual diode current is zero?

No. It only shows the positive-resistor target calculation is not available under the entered fixed-drop assumptions.

Does the result select an automotive-rated component?

No. It performs a fixed-drop scenario calculation.

Why can candidate current differ from target current?

The entered candidate resistance can differ from the calculated ideal value.

Find your calculator

Start typing to explore the library.