Unit converters

Height converter for feet inches metres and centimetres

Convert a measured height between split imperial and metric units, with decimal totals and readable feet-and-inches output.

Your numbers

Calculated on your device. Your inputs aren’t sent to us.

Your result

Ready when you are

Enter your inputs and select Calculate.

Report an issue

Try it, understand it

Explore the result

Keep the whole unit and its remainder separate, then compare the total value with the readable rounded display.

Worked example comparison
ExampleOutputWhat to notice
Five feet ten inchesTotal centimetres177.8 cm70 inches is exactly 177.8 cm.
One metre seventy-eight centimetresTotal centimetres178 cm178 cm converts back to about 5 ft 10.0787 in.
A remainder close to the next footTotal centimetres182.8799746 cmThe split display rounds 11.99999 inches up and carries a whole foot, while the numeric total retains its own value.

Check your understanding

Is 5.10 decimal feet the same as 5 ft 10 in?

No. Decimal feet use a fraction of a foot; split inches use twelfths.

Does an exact factor make a measured height exact?

No. The original measurement may already be rounded or uncertain.

Behind the numbers

How this calculation works

Combine the whole-unit part with its remainder, then convert using the exact international inch: 2.54 centimetres. Report both decimal totals and split-unit measurements. For readable output, whole feet or metres are separated from the remainder; display rounding carries a remainder of twelve inches or one hundred centimetres into the next whole unit.

THE FORMULACentimetres = (12 × feet + inches) × 2.54; inches = centimetres ÷ 2.54

A worked example

Five feet ten inches is 5×12+10 = 70 inches. At exactly 2.54 cm per inch, that is 177.8 cm, 1.778 metres, or 1 metre 77.8 centimetres. Conversely, entering 1 metre and 78 centimetres gives 178 cm and about 5 feet 10.0787 inches.

Good to know

Measurement conversion only, not a height-growth prediction or medical assessment. Feet and metres are nonnegative whole numbers; inch and centimetre remainders may have decimals but must stay below 12 and 100 respectively. Split-unit displays round to four decimal places. Input precision does not prove measurement accuracy.

A split measurement is not a decimal measurement

Feet and inches are two parts of one length. Five feet ten inches means five complete feet plus ten additional inches. It is not 5.10 decimal feet. To express that measurement as decimal feet, divide the inch remainder by twelve and add it to the feet: 5+10/12 = 5.833333 feet.

Metres and centimetres use a different remainder scale. One metre seventy-eight centimetres is 1+78/100 = 1.78 metres. This calculator deliberately provides separate fields so the written measurement keeps its intended meaning. Use the length converter when you already have a single decimal value in one unit.

The international inch is exactly 2.54 centimetres, so the conversion factor does not depend on the person being measured or on the country in which the measurement was taken. Measurement accuracy still depends on the original observation. Converting a rounded inch reading cannot recover centimetre detail that was never measured.

The Mosteller body surface area calculator requires height in centimetres with weight in kilograms. The measured somatotype calculator uses centimetres for lengths but millimetres for skinfolds, so check each field’s units before entering measurements.

Rounding should not create twelve leftover inches

A readable feet-and-inches result first separates whole feet from the remaining inches. If rounding makes that remainder equal twelve, the display must carry one additional foot and show zero leftover inches. The corresponding metric rule carries one metre when a rounded centimetre remainder reaches one hundred. This avoids outputs such as 5 ft 12 in.

The total-centimetres and decimal-metres results are calculated before the split-unit display is rounded. That keeps the numeric conversion separate from how a human-readable measurement is written. Zero length converts to zero in each representation rather than being treated as an absent value.

This page converts a height measurement. It does not use age, parental measurements, growth charts or a formula for predicted adult height. It also does not judge whether a particular height is healthy. For a unit-based physical calculation, keep the chosen length unit consistent with the other inputs instead of substituting a feet-and-inches string into a decimal field.

A few questions, answered

Can I enter 5.5 in the feet field?

No. That field is whole feet. Enter 5 feet and 6 inches for a total of 5.5 decimal feet.

Why must the inch remainder be below 12?

Twelve complete inches belong in the feet count. The second field is only the part left after complete feet have been separated.

Does the converter predict adult height?

No. It converts the measured length you supply; no growth prediction is made.

Find your calculator

Start typing to explore the library.