Home & construction

Multi-room floor area calculator

Total rectangular room sections, subtract measured exclusions and convert square metres and square feet.

Your numbers

One nonoverlapping rectangle per line or semicolon. Use 2 or 3 numbers: length, width, excluded area. The third entry is already an area, not another length. All lengths use the selected unit.

Calculated on your device. Your inputs aren’t sent to us.

Your result

Ready when you are

Enter your inputs and select Calculate.

Report an issue

Try it, understand it

Explore the result

Compare net measured area with an unadjusted rectangle total, then read the same area concept in square feet.

Worked example comparison
ExampleOutputWhat to notice
Two rooms with an exclusionNet floor area17 m²The first room contributes 12 − 1 = 11 m²; the second adds 6 m², giving 17 m².
The same rooms without exclusionsNet floor area18 m²Without the 1 m² exclusion, the total is 18 m². No material-waste allowance has been added.
One ten-foot square roomNet floor area100 ft²10 ft × 10 ft = 100 ft², equivalent to 9.290304 m². Read the unit beside each result.

Check your understanding

Before checking: is the third row entry another length?

No. It is an already calculated excluded area in m² or ft², matching the selected length unit.

Can overlapping rectangles be added as if they were separate rooms?

No. Their overlap would be counted twice. Divide the measured floor into nonoverlapping sections or account for the overlap explicitly.

Behind the numbers

How this calculation works

Divide the measured floor into nonoverlapping rectangles. Subtract any entered excluded area from its own section, total the results and convert using the exact international foot. Section rows preserve the contribution of each room.

THE FORMULANet area = Σ(length × width − excluded area)

A worked example

A 4 m × 3 m room excluding 1 m² contributes 11 m². Adding a 3 m × 2 m room gives 17 m² net.

Good to know

A geometric material-planning estimate from the entered measurements. Check actual product dimensions and the project layout. No structural suitability, installation specification, local requirements, labor, tax or pricing is determined. Decimal input lists allow up to 6 places and at most 100 entries/rows, each no greater than 1,000,000.

Count each part of the floor once

A floor plan can be divided into rectangular rooms or smaller rectangular sections. Add those areas only when they do not overlap. An L-shaped room can be split into two rectangles, but using two full bounding rectangles can count the corner intersection twice.

The optional third entry is an excluded area in the square of the selected length unit. For a 4 m by 3 m section, entering 1 subtracts one square metre. It does not describe a one-metre strip; such a strip needs its width and length multiplied first.

The result table keeps each section’s gross area, exclusion and net contribution visible. A zero net section is permitted when its entire rectangle is excluded, but an exclusion larger than its own section is rejected rather than offset against another room.

Separate measured area from purchasing area

A flooring material cost calculation can add an entered purchasing allowance to measured floor area. Do not add that allowance here and then add the same percentage again downstream. The measured net result and a material-order quantity answer different questions.

Use the area converter when you need additional square-area units. The international foot is exactly 0.3048 metres, so its area factor is 0.3048 squared; a length factor must not be applied unchanged to a floor area.

This calculator does not select a property-measurement standard or decide whether wall thickness, cupboards, stairs or balconies should count. Define the measurement boundary for your own task before taking dimensions. Ceiling height and wall surface area cannot be inferred from floor area alone.

A few questions, answered

Can I enter an irregular room?

Divide it into nonoverlapping rectangular sections that represent your measurement. Curves or coordinate-defined boundaries need an appropriate shape or polygon method.

Does the excluded-area column use the length unit?

It uses its square: m² when lengths are metres, or ft² when lengths are feet.

Does the result include material waste?

No. It is net measured area. Purchasing allowances belong in the material calculation where their meaning can be kept explicit.

Find your calculator

Start typing to explore the library.