Home & construction

Tile quantity calculator

Estimate a whole-tile purchase count from area and tile dimensions.

Your numbers

Calculated on your device. Your inputs aren’t sent to us.

Your result

Ready when you are

Enter your inputs and select Calculate.

Report an issue

Try it, understand it

Explore the result

Compare these worked scenarios while keeping the units and assumptions visible.

Worked example comparison
ExampleOutputWhat to notice
Known areaTiles to purchase44 tilesTen square metres with half-metre sides and ten-percent allowance gives 44 tiles.
Rectangular roomTiles to purchase53 tilesA four-by-three-metre room needs 53 half-metre-square tiles at the stated allowance.
Original project workflowTiles to purchase59 tilesTen by twelve feet with 1.5 ft tile sides gives 59 tiles at ten-percent allowance.

Check your understanding

Are room dimensions available as well as known area?

Yes. Select rectangular-room mode and use the same selected length unit for room and tile sides.

Is the price per tile or per square metre?

Per tile; it multiplies the final whole-tile purchase count.

Behind the numbers

How this calculation works

Tile dimensions are converted from centimetres to metres before calculating area. The count is rounded up after applying the allowance. This is an area-based estimate, not a layout plan.

THE FORMULATile count = ceiling(area ÷ tile area × (1 + allowance/100))

A worked example

For 10 m² using 50 × 50 cm tiles, 40 tiles cover the area; a 10% allowance gives 44 tiles.

Good to know

Ignores grout width and specific cutting patterns. Pack-size rounding, edge pieces and supplier-specific waste allowances need separate review.

A little curiosity

Area coverage is not a cutting layout

Forty 50 by 50 cm tiles have a combined face area of 10 m². A room of that area can still need extra tiles because the boundary cuts and pattern may not let every offcut be reused.

That is why the allowance is separate from geometric coverage. A diagonal pattern, irregular room or fragile material can behave differently from a simple rectangular layout. The default allowance is an editable estimate, not a universal requirement.

The flooring material cost model turns a supplied area and waste assumption into a material budget; tile counting adds a separate whole-piece rounding requirement. The tile grout quantity calculator with joint depth estimates filled joint volume and product-specific mass rather than counting the tiles themselves. The floor paver grid and running bond layout calculator counts clipped boundary cells with an optional alternate half-paver row offset.

Convert tile dimensions before combining areas

The surface area is in square metres but tile sides are entered in centimetres. The tool multiplies the tile sides and divides by 10,000 to convert square centimetres to square metres.

Grout width, edge trim and pack sizes are not modeled. Check whether the supplier sells by tile, pack or nominal coverage, then round the purchase accordingly. The tool rounds an estimated count to whole tiles only.

An area estimate is not a cutting plan

Known-area mode retains square-metre surface input and centimetre tile sides. Rectangular-room mode accepts both room and tile dimensions in one selected length unit, restoring the original project workflow without mixing feet and centimetres. Multiply the two tile sides before dividing the surface area by one tile’s area.

The area and perimeter calculator explains why two surfaces with the same perimeter can require different amounts of covering. Tile demand follows area, while edge cuts and borders follow a layout. This tool does not pretend that an area ratio describes how every cut piece can be reused.

Price applies to the final whole-tile count

Apply the entered percentage allowance to the unrounded area-equivalent count, then round upward once. Multiplying the per-tile price by that final purchase count retains the cost of the extra whole tile. Rounding the base count first and then applying waste would be another convention and can produce a different answer.

The roofing material calculator also separates geometric area, an explicit allowance and package coverage. For tiles, grout spacing, patterns, pack quantities, breakage and edge requirements remain outside the model. Price is per tile rather than per square metre; changing a currency label formats the same entered amount and does not convert it.

A few questions, answered

Does this include grout spacing?

No. It uses the tile face dimensions and a separate allowance.

Why is the answer rounded up?

A fractional tile cannot normally be purchased as a full usable tile; the estimated purchase count uses whole tiles.

Are room dimensions available as well as known area?

Yes. Select rectangular-room mode and use the same selected length unit for room and tile sides.

Is the price per tile or per square metre?

Per tile; it multiplies the final whole-tile purchase count.

Does the count optimize cut reuse?

No. It is an area-based estimate with an explicit allowance.

Find your calculator

Start typing to explore the library.